Da Vinci Tribology

What is friction?

Friction Definition

Friction is a force acting opposite to the direction of relative motion. Friction rises on the interface between bodies, but may also develop within the body.Examples of the latter include air and hydrodynamic friction, where the friction rises between the fluid layers. Friction is not a fundamental force, but rather a manifestation of electro-magnetic and gravity forces. There are many sources of friction: deformation of the surfaces, adhesion, capillary forces, van der Waals forces, chemical bonding, etc. Friction is a non-conservative force and the energy spent to overcome friction is lost. Friction losses reduce the energy efficiency of many mechanical devices. A recent report on the energy consumption due to frictional losses in passenger cars estimates that only 21.5% of the potential fuel energy is used to move the car, whereas direct frictional losses account for 33% (28% if breaking is excluded). Within these losses, 35% is used to overcome tire-road friction, 35% to overcome engine friction, 15% – transmission and 15%  brake contact friction. So one of the major challenges of the modern tribology is to find new technologies to reduce friction and increase energy efficiency.

In general, friction can be dry or lubricated. For a vast majority of the surfaces encountered in nature and used in industry, the source of dry friction is the imperfections of the surfaces. It turns out that even mirror shining surfaces are actually not flat, at least at micro- and nano- scales, and contain hills and valleys. These imperfections are called surface roughness. A typical Atomic Force Microscopy measured surface profile of a smooth clean glass plate is shown below.

AFM clean glass
AFM height profile and cross-section of clean glass plate

When this rough surface is dragged against another rough surface, these valleys and hills will interlock with each other, deform and consequently oppose the motion. The classical example of the interlocking are the stalled egg cartons type surfaces, which are hard to slide against each other (due to high friction) as shown in he figure below. The force needed to overcome this interlocking is friction.

Egg Carton
Egg carton type surfaces. Source:

At the same time, producing atomically flat surfaces does not solve the problem of friction reduction. Actually the decrease of roughness to atomically flat level for engineering materials, such as steels, for example, leads to a much higher dry friction! And this is due to an increase of the adhesion forces (van der Waals interactions, capillary forces, etc.).

In order to reduce friction the lubrication theory is used (hydrodynamic or elastohydrodynamic). This approach introduces a lubricant film between rough surfaces and the direct contact between rough surfaces is either eliminated or minimized. The friction in this case is determined mostly by the shear of lubricant layers, rather than shearing of solids, as shown in the figure below:

Lubricant Film Shear
Lubricant Film (From: Lubrication for Industry, by Ken Bannister, Industrial Press)

In such case, the interlocking and adhesion effects are reduced. For most engineering materials, dry friction is larger than lubricated since the shear strength of the solids is typically larger. However, the theory has reached its fundamental limit (0.01-0.04 friction coefficient) and cannot be used to reduce the friction further. Therefore, the researchers look for other ways to reduce friction and recently several cases of superlubricity (friction coefficient well below 0.01) were reported (look further on tribonet).

Laws of Friction

Leonardo da Vinci was the first to perform a systematic analysis of friction. He formulated the laws of friction, but his works were not discovered until recently. These laws are formulated for the case of dry friction. There are 3 laws of friction:

  1. Amontons’ First Law: The force of friction is directly proportional to the applied load.
  2. Amontons’ Second Law: The force of friction is independent of the apparent area of contact.
  3. Coulomb’s Law of Friction: Kinetic friction is independent of the sliding velocity.

Kinetic friction is the defined as the friction developed during relative motion, while static is the force developed prior the motion starts. Typically, the kinetic friction is smaller than the static.

Take a look at this video for further information:

Administration of the project

Be the first to comment

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.