Pressure-Viscosity Coefficient and Characteristics of Lubricants

TriboNet

December, 8 2019
piezo-viscous equation

Variation of Viscosity with Pressure

Primary purpose of any industrial lubricant is to maintain a satisfactory lubricating film in between contacting surfaces; and importance of viscosity to achieve this is univocally known in industrial maintenance practices. However, what is often overlooked in such easy comprehension on lubricant’s viscosity is the gap between the effective viscosity and quoted (laboratory measured) viscosity of any lubricant. Lubricant’s viscosity may be physically and/or chemically affected by a number of factors; however, some of the prominent influencing agents are temperature, pressure, and shear stress. These influences in turn depends on friction, load, speed, and machine operating environments. In addition, lubricant’s chemical make-ups and any alteration to it during operation are some of other important causes to influence a lubricant’s effective viscosity. Thereby, it can be inexplicably understood that the laboratory measured viscosity is dramatically different than the viscosity which is effective inside the system during operation. This difference is unavoidable since any mechanical system is exposed to the fluctuation of the environmental and mechanical operating factors (temperature, load, speed, friction, etc.).

Any industrial lubricant’s viscosity is often found to be quoted in manufacturer’s catalog in terms of the standardized unit. However, these quoted viscosities are usually measured in laboratories at atmospheric pressure and often with bench-test instruments such as falling weight type viscometers. Major limitations of these instruments are the availability of the limited range of low shear stresses. However, the effects of shear stress on viscosity can now be captured up to good extent with the help of advanced rheometer facilities which are commercially available and being continuously optimized. Further, the temperature-viscosity characteristics is also well understood and standard characteristic features for lubricants such as viscosity index has been well recognized. Nevertheless, the pressure-viscosity characteristics of lubricants still remains largely elusive in broader industrial practices.

Pressure induced variation in viscosity can often be a tackling issue in lubricant’s performance in the system. Increase in pressure over a confined lubricant often results in increasing the lubricant’s viscosity (Hersey and Shore [1928]). Such change in viscosity under mechanical pressure is also known as piezo-viscous effects. This situation is likely to prevail in certain regimes such as mixed and elasto-hydrodynamic lubrication. In several instances, especially in non-conformal, highly concentrated, and heavily loaded contacts such as in ball/roller bearings, gears, cams, etc., the contact pressure often becomes several order higher than atmospheric pressure. It is therefore of practical importance to assess and quantify the pressure-viscosity behavior of any lubricant in order to assess its effectiveness inside the system under varying degrees of operating pressures.

Viscosity-Pressure Equations

Several investigations on the pressure-viscosity behavior of fluids were reported over the preceding decades; and some form of empirical correlations were also fitted to these experimental data (So and Klaus, 1980). The most primitive, but, most popular and simple one is the Barus equation proposed in 1893:

banner

(1)    \begin{eqnarray*} \eta = \eta_0 e^{\alpha p} \\ \end{eqnarray*}

where   \eta_0   is the viscosity at atmospheric pressure and α is the pressure-viscosity coefficient.

Mathematically, α is the tangent to the Barus equation curve at zero pressure. This coefficient has been frequently used in analytical formulations of elasto-hydrodynamic lubrication. In some cases, the slope of a secant of the Barus equation is used to estimate the coefficient. Such secant is drawn between 0 and any other point up to 0.1 GPa. It is important to note here that α is ideally a pressure independent and a temperature sensitive coefficient. However, it has been repeatedly mentioned in literature about the significant error that the Barus equation yields at elevated pressures above 0.5 GPa. A case study is reproduced here in Fig.1 (Sargent Jr, 1983). It appears that as pressure rises, the coefficient, α, loses its independence from pressure; alternatively, the use of the slope of secant (α*) exhibits closer prediction but not satisfactorily free from errors. Therefore, the challenges still persist to accurately capture the piezo-viscous characteristics of lubricants.

In follow-ups of the Barus equation, a couple of empirical correlations emerged and have been used by subsequent researchers. Some of these correlations are furnished in Table 1. It is important to note here that these equations are not exhaustive and based on pure empirical means. The common purpose of these empirical correlations are to estimate the coefficients (sometime called the pressure-viscosity coefficients such as α in case of the Barus equation) with a handful of experimental data and then to use these coefficients in the correlation to predict viscosity at a given pressure. However, more often than not, such empirical approaches are applicable only for a limited range of its variables (read ‘pressure’, ‘temperature’, ‘shear stress’, etc. in this context) and some other times they appear too obscure to comprehend and implement in engineering calculations.

Pressure-viscosity dependence
Fig. 1: Pressure-viscosity dependence curve under isothermal conditions (at 37.80C) for a lubricant, α* is the slope of the secant between 0 and 0.1 GPa (data collected from Sergeant Jr. [1983]).

Table 1: Empirical models for lubricant’s pressure-viscosity characteristics (Sargent Jr. [1983])

banner
Author Empirical Models
Barus [1893]  \eta = \eta_0 e^{\alpha P}
Chu and Cameron [1962]  \eta = \eta_0 (1+CP)^n
Roelands et al. [1963]*  \eta' = \eta_0' (1+0.005P)^Z
Sargent Jr. [1983]  \eta = \eta_0 e^{AP/B P}
Nomenclature: η=viscosity in Pa-s at any given pressure; η0=viscosity in Pa-s at atmospheric pressure; A, B, C, n, z and α are empirical coefficients in respective equations; η/= 103(η+0.0012); η0/=1030+0.0012)

Despite all the anomalies, almost all of these correlations estimate the viscosity as an exponential function of pressure. This manifests the possibility of dramatic increase in the viscosity of lubricants with respect to rise in pressure. Thereby, under piezo-viscous situation, increase in contact pressure may result in thickening of the lubricating fluid. Overall, this means, an incremental pressure rise may at some point be detrimental to a lubricant’s performance. Intuitively, thickening of lubricant may seize the lubricant’s flow and leading to a failure of lubrication, in other words, by lubricant fracture!

Further, it can be interesting and important to examine the influence of pressure on lubricant’s effective viscosity as a function of the lubricant’s chemical composition. Figure 2 shows some already examined cases (data reported in Sargent Jr. [1983]) with different lubricating oil under similar pressure and temperature. The ordinate of the graph represents the ratio of a particular lubricant’s viscosities measured at 980C and 380C, respectively.

Effects of chemical make-up on pressure-viscosity characteristics of lubricants
Fig. 2: Effects of chemical make-up on pressure-viscosity characteristics of lubricants (data from Sargent Jr. [1983)].

These data show that the pressure also influences the lubricant’s temperature-viscosity characteristics. In order to interpret this graph, the reader may note that the more the value of the ratio, η10040, is, the better is its viscosity-temperature characteristics. Interestingly, synthetic composition such as silicone oil exhibited to be most susceptible to the influences of pressure. In general, silicone oil exhibit better resistance against temperature induced viscosity drop at atmospheric pressure, however, this resistance probably loosens up under pressure. Counter intuitively, it can also be understood that while increase in pressure gives rise to viscosity, increase in temperature does the opposite; therefore, a lubricant’s declining resistance against temperature under pressure may at some instances be advantageous to the system. However, in order to arrive at such trade-offs, especially with the advent of new type of lubricants, we look forward to analyze more data to interpret the combined effects of temperature, pressure, shear stress, and new age lubricant’s wonder chemical make-ups; hopefully, in an upcoming discussion.

Viscosity-Pressure Calculator

In general lubricants used in industry are subject to high pressures (up to several GPa). At high pressures, lubricants viscosity increases significantly and thus this increase should be taken into account in calculation of the central film thickness or friction in the contact. The calculator below allows calculating viscosity for a given pressure using the 2 most common equations, Barus and Roelands. Please find the description below or here.

Here is a table of typical pressure-viscosity coefficients of several lubricating oils.

Lubricants Dynamic visc η0
[mPas]
Pressure-visc
coeff α [10-9 m2/N]
30 60 100 30 60 100
High VI oils
Light machine oil 38 12.1 5.3 18.4 13.4
Heavy machine oil 153 34 9.1 23.7 20.5 15.8
Heavy machine oil 250 50.5 12.6 25.0 21.3 17.6
Cylinder oil 810 135 26.8 34.0 28.0 22.0
Medium VI oils
Spindle oil 18.6 6.3 2.4 20 16 13
Light machine oil 45 12 3.9 28 20 16
Medicinal white oil 107 23.3 6.4 29.6 22.8 17.8
Heavy machine oil 122 26.3 7.3 27.0 21.6 17.5
Heavy machine oil 171 31 7.5 28 23 18
Low VI oils
Spindle oil 30.7 8.6 3.1 25.7 20.3 15.4
Heavy machine oil 165 30.0 6.8 33.0 23.8 16.0
Heavy machine oil 310 44.2 9.4 34.6 26.3 19.5
Cylinder oil 2000 180 24.0 41.5 29.4 25.0
Other fluids / lub’s
Water 0.90 0.47 0.28 0 0 0
Castor oil 360 80 18.0 15.9 14.4 12.3
Glycerol 535 73 13.9 5.9 5.5 3.6
PP glycol 750 82.3 17.8
PP glycol 1500 177 17.4
Tri-arylphosphate ester 25.5 31.6

About the Author

Sandip Panda

([email protected])

(https://www.linkedin.com/in/sandip-panda-phd-iit-kharagpur-89907162/)

References:

  1. Hersey M. D. and Shore H., 1928, Viscosity of lubricants under pressure, Mech. Engg., 50, pp 221–232.
  2. So, B. Y. C. and Klaus, E. E., 1980, Viscosity-pressure correlation of liquids, ASLE Trans., 23 (4), pp 409–421.
  3. Sargent Jr L. B., 1983, Pressure-viscosity coefficients of liquid lubricants, ASLE Transactions, 26 (1) pp 1-10.
  4. Stachowiak, G. W. and Batchelor, A. W., 2000, Engineering Tribology (Second Edition), Butterworth-Heinemann, United Kingdom.

Administration of the project